Philips Adult Hard Shell SpO2 Sensor 3.0m (Masimo SET Technology 8-Pin Reusable New)

The Philips Masimo SET SpO2 sensor is a reusable adult hard shell finger clip pulse oximetry probe that works with Philips patient monitors equipped with Masimo SET oximetry, such as the IntelliVue MP40, IntelliVue MX700 (Masimo Rainbow) and SureSigns VS4. It measures oxygen saturation (SpO2) and pulse rate non-invasively through a 3.0 m (9.8 ft) cable ending in a Philips-style 8-pin connector.

Key Benefits of This Philips Masimo SET SpO2 Sensor

• Masimo SET signal processing: Built for motion-tolerant, low-perfusion-tolerant SpO2 readings on supported Philips monitors.
• Reusable hard shell design: A durable finger clip that can be cleaned and reused across patients, lowering cost per reading compared with disposables.
• Long 3.0 m cable: Gives staff room to position the monitor away from the bed without extension cables.
• Plug-and-play fit: Philips-style connector plugs directly into the Masimo SET SpO2 port of supported monitors.
• Quality assured:

Features of the Adult Hard Shell Finger Clip Sensor

Rigid Clip Housing

The hard shell body holds the emitter and detector in consistent alignment across the fingertip, supporting stable readings during spot checks and continuous monitoring.

Spring-Loaded Finger Clip

A spring hinge secures the sensor on an adult finger without tape, making quick placement and repositioning easy between patients.

Flexible Shielded Cable

The 3.0 m cable is designed for repeated flexing and routine wipe-down cleaning in busy clinical areas.

 Specifications : Philips Masimo SET SpO2 Sensor

Cross-Reference Part Numbers

Works With These Philips Monitors

• Philips IntelliVue MP40
• Philips IntelliVue MX700 (Masimo Rainbow)
• Philips SureSigns VS4

Please confirm that your monitor uses a Masimo SET SpO2 module before ordering. Philips monitors fitted with Philips FAST SpO2 require a FAST sensor instead.

Use Cases for an Adult Reusable SpO2 Sensor

• Continuous SpO2 monitoring in ICU, high-dependency and step-down units
• Spot checks and vital-sign rounds on general wards
• Post-anaesthesia recovery (PACU) and procedural sedation
• Emergency department and in-hospital transport monitoring
• Replacing worn or damaged reusable finger sensors on existing Philips Masimo SET monitors

Application and Care

• Place the adult finger in the clip so the fingertip rests against the internal stop, with the cable running along the back of the hand.
• Avoid fingers with nail polish, artificial nails or restricted circulation.
• Change the measurement site regularly during long-term monitoring.
• Clean and disinfect between patients according to your facility’s infection-control protocol, wiping the surfaces rather than soaking the sensor.

Frequently Asked Questions

Which monitors does this Philips Masimo SET SpO2 sensor work with?

It works with Philips monitors fitted with Masimo SET pulse oximetry, including the IntelliVue MP40, IntelliVue MX700 (Masimo Rainbow) and SureSigns VS4.

Will it work on a Philips monitor with FAST SpO2?

No. This sensor is designed for the Masimo SET SpO2 input. Monitors using Philips FAST SpO2 need a FAST-technology sensor such as the M1196A family.

Is this SpO2 sensor reusable?

Yes. It is a reusable hard shell finger clip sensor that can be cleaned and used on multiple adult patients.

How long is the cable?

The cable is 3.0 m (approximately 9.8 ft) long.

What part numbers does it cross-reference?

It cross-references Masimo LNC-MP and Unimed U410-91M / U410-91MR.

Is the sensor new, and does it carry a warranty?

Yes.

Related SpO2 Sensors

Looking for other options?

See the Philips Masimo SET Adult Ear Clip SpO2 Sensor 3.0m, the Philips M1196AL Adult Hard Shell SpO2 Sensor 3.0m (FAST), the Philips M1191BL Adult Soft Tip SpO2 Sensor 3.0m, the Masimo 2054 DCI Adult Hard Shell SpO2 Sensor 3.0m and the Masimo 1396 DCSC Adult Hard Shell SpO2 Sensor 1.0m.