Datex Ohmeda OXY-W4-N Neonate Wrap SpO2 Sensor 3.0m (New)

A Datex Ohmeda neonate wrap SpO2 sensor is a reusable pulse oximetry probe that wraps gently around a newborn’s foot or hand to measure blood oxygen saturation (SpO2) and pulse rate on Datex Ohmeda and GE Healthcare TruSignal patient monitors. This brand-new 3.0m sensor is built to the Datex Ohmeda OXY-W4-N reference specification and terminates in a 10-pin round direct-connect plug, so it goes straight into a supported bedside monitor without an extension or adapter cable.

Key Features & Benefits

• Gentle wrap design – soft, flexible band shaped for delicate neonatal skin and small anatomical sites.
• 10-pin direct-connect plug – works with Datex Ohmeda and GE TruSignal monitor ports with no adapter cable required.
• 3.0m (9.8 ft) cable – enough reach for incubators, bassinets, and bedside monitoring setups.
• Reusable construction – lowers per-patient monitoring costs compared with single-use adhesive pads.
• Stable low-perfusion performance – engineered to hold a steady signal even with the weaker peripheral circulation common in newborns.
• with a 12-month warranty.
• Brand-new condition, built to the OXY-W4-N / Unimed U310-09 reference specifications.

Technical Specifications of Datex Ohmeda Neonate Wrap SpO2 Sensor

Works With These Monitor Models

This sensor’s 10-pin direct-connect plug is built to the same reference as the Datex Ohmeda OXY-W4-N and Unimed U310-09, so it goes onto the monitor families below. Please confirm your exact model and connector before ordering.

Datex Ohmeda & GE Healthcare Monitors

• Aespire, Aespire 15
• AS/3, AS/3 Compact, AS/3 with M-series modules
• Capnomac Ultima
• Cardiocap I, Cardiocap II, Cardiocap S/5 Light, Cardiocap/5
• CG/2S, CH-RS, CH/2S, CH/S
• CS/3, CS/3 with M-series modules, CS/5, CS/5 Compact
• Light Monitor, M-ESTP, M-NESTPR, M-PRESTN
• Oscar II, OSP-200
• S/5, S/5 with M-series modules
• Satellite, Satellite Plus II, Satellite Trans
• System 5, Trans Plus
• TruSignal-equipped monitors
• ULTS00, ULTSIO, ULTSVI, ULTSVO
• GE Healthcare Datex Ohmeda S5

Use Cases

• Continuous SpO2 and pulse-rate monitoring in the NICU
• Pediatric ward and delivery-room bedside monitoring
• Transport incubators
• General newborn ward observation

Care & Maintenance

• Wipe down with an approved hospital-grade disinfectant between patients.
• Keep the connector end dry – do not soak or submerge it.
• Store flat, away from direct sunlight and sharp edges.
• Inspect the wrap and cable for wear or cracking before each use.

Related SpO2 Sensors

Rounding out a NICU or GE/Datex Ohmeda monitoring bay:

• GE TruSignal Reusable SpO2 Sensor TS-SA4-GE
• Reusable SpO2 Sensor, Infant Neonate Wrap, 9 Pins
• DS-100A DB9 Pin SpO2 Sensor, OxiMax Neonate Wrap
• Infant Wrap SpO2 Sensor, Non-OxiMax, 7 Pins
• Neonate Wrap SpO2 Sensor, Non-OxiMax, 7 Pins

Frequently Asked Questions

What is a Datex Ohmeda neonate wrap SpO2 sensor used for?

It measures blood oxygen saturation (SpO2) and pulse rate on newborns. The sensor wraps gently around a foot or hand and plugs into a Datex Ohmeda or GE TruSignal patient monitor.

What connector does Datex Ohmeda Neonate Wrap SpO2 Sensor use?

A 10-pin round direct-connect plug built to the Datex Ohmeda OXY-W4-N (Unimed U310-09) reference, so it plugs straight into the monitor without needing an extension cable.

How long is the cable?

3.0 metres (9.8 feet), which gives enough reach for incubator and bedside setups.

Is Datex Ohmeda Neonate Wrap SpO2 Sensor reusable?

Yes. It is a reusable probe rather than a single-use adhesive pad, so it can be cleaned and reapplied across patients when standard hospital disinfection protocols are followed.

Is this a new or refurbished sensor?

This is a brand-new sensor.

Which monitors does it work with?

It works with Datex Ohmeda and GE Healthcare monitors built to accept the 10-pin OXY-W4-N / TruSignal connector, including the Aespire, AS/3, S/5, and Cardiocap families. Always confirm your exact monitor model before ordering.